Power factor of installations and power control in inverters

After the introduction of the photovoltaic system, the power factor of the installation is reduced by injecting active power from the solar panels. The power factor correction can be performed by the photovoltaic inverter itself or by capacitor banks.

In addition to power factor correction, the power control feature (active or reactive) of inverters can be used to support voltage control in long distribution networks or autonomous networks.

The power factor of electrical installations

Electricity consumers are divided into ranges according to their supply voltage, according to the tables below.

Consumers in Group A must have their power factor measured using an hourly average calculation. The reference (calculated) power factor cannot be less than 0,92, under penalty of fine for excess reactive energy consumption.

In conventional electrical installations (without the presence of photovoltaic systems) the power factor has always been a cause for concern. The causes of low power factor are high-power induction motors operating at no load (as is common in machine tools), empty or under-loaded transformers, fluorescent lamps and the presence of many low-power motors (in refrigerators and appliances). air conditioning, for example), among other things.

The power factor can also be reduced by the presence of many non-linear equipment such as welding machines, electronic lamps and circuits with rectified input in general. REN 414 (Normative Resolution No. 414/2010) and REN 569 (Normative Resolution No. 569/2013) Of the ANEEL (National Electric Energy Agency) regulate the definition, reference values ​​and scope of application of the power factor for billing excess reactive power from consumer units.

According to these resolutions, Group B consumer units cannot be charged for excess reactives due to the low power factor. For Group A consumer units, the power factor, for billing purposes, must be verified by the distributor through permanent measurement.

The power factor of these consumers has a minimum limit of 0,92. If the consumer has a power factor below this value, a fine for excessive use of reactive energy will be charged. Power factor control in conventional installations, in Group A consumers, is carried out through capacitor banks associated with supervision and control systems.

A power meter monitors active power and reactive power consumption. As necessary, depending on the loads used in the installation (motors and other equipment), a greater or lesser number of capacitors are added to the installation.

This is a technologically simple solution and is widely used in all types of commercial or industrial consumers who have problems with the power factor and have a lot of intermittency in their demand curve (that is, they have machines that go in and out of operation all the time ).

Power factor x photovoltaic systems

Inverters grid-tie They inject active energy produced by photovoltaic modules into the electrical installation. The injection of active power worsens the power factor of the installations, as from the distributor's point of view the consumer starts to use less active energy from the electrical grid, which increases their reactive energy consumption proportionally.

Despite not causing any change in reactive energy consumption, photovoltaic systems cause a reduction in the power factor in Group A consumers.

Photovoltaic systems inject active power, which causes a reduction in the power factor of the installations, although the reactive power consumption is not changed.

Reactive power control through inverters

The inverters grid-tie for photovoltaic systems it has the ability to inject reactive power. In this way, they function as electronic capacitors or inductors. By controlling the phase shift of the electric current, the inverter is capable of producing inductive or capacitive currents.

The secret to the ability to control reactive power is the inverter's output current control system. This system makes the inverter behave like a controlled current source. We can ask the inverter to generate any type of current, of any amplitude, frequency or phase.

The output current of the photovoltaic inverter is always sinusoidal and synchronized in frequency with the electrical grid voltage. Depending on the amount of active or reactive power that is desired at the inverter output, the amplitude or phase of the current can be changed by the with inverter control.

Although it is possible to correct the power factor of the installations with the injection of reactive power by the inverter, three main facts must be remembered:

• The inverter's power factor injection feature is not intended to replace capacitor banks, but only to provide adjustments to the reactive supply to improve power factor or support voltage and frequency control on weak electrical grids. which can be end-of-line distribution networks, with high impedance, or autonomous networks (micro-grids);

• Using the inverter's reactive power injection capability reduces its ability to inject active power. Inverters used for this function must generally be oversized.;
• The inverter only provides a small portion of reactive power, defined by a capacity curve. This means that in the absence of active power, the inverter does not have the capacity to inject reactive power. It is not possible, for example, to perform nighttime power factor compensation with an inverter grid-tie.

If the inverter is programmed to generate only active power, the output current is always synchronized in phase with the voltage. If we want the inverter to produce reactive power, the phase between current and voltage will be changed according to the type of injection and according to an algorithm pre-programmed in the inverter.

Inverter power control modes

Most inverters grid-tie It has pre-programmed reactive power control modes. The different modes can be used according to the objective to be achieved with the injection of reactive power or the limitation of active power in the installation.

What all modes have in common is the control of the portions of active and reactive power injected by the inverter into the electrical grid. What changes from one mode to the other is the size of each installment and the way they are adjusted.

Active power limitation

In this mode, the inverter limits the power extracted from the modules by reducing its input voltage. Reducing active power is one of the ways to control the power factor value of an installation, preventing excessive injection of active energy. This way, the inverter's output power can be adjusted to a percentage value of the power consumed in the installation.

In reality, this control mode is very useful in situations where you want to avoid the export of active power to the electrical grid, ensuring that the inverter will only inject the energy necessary to be consumed locally.

Furthermore, this control mode can be useful for autonomous networks that have another power source in parallel – such as a diesel generator, for example. By limiting the inverter's power, it is possible to prevent the diesel generator from receiving excess energy from the system when solar generation is very large, but there is no consumption.

P xf control – active power limitation

Controlling active power as a function of frequency is useful for controlling the frequency of autonomous electrical networks. Although this control mode is not necessarily associated with the need to control the power factor of the installations, it is interesting to include it here.

The following figure shows an active power curve (P) as a function of network frequency (f). In photovoltaic systems connected to the distribution network, frequency is not a variable that can be changed. In autonomous networks, however, the bus frequency may increase if there is excess active power. This frequency increase can be contained by limiting the inverter output power.

P x U control – active power limitation

The control of active power as a function of voltage is similar to the previous mode, however the reference variable is the bus voltage and not the frequency.

Reactive power control

The following figure illustrates the situation in which the inverter simultaneously supplies active and reactive power to the electrical grid. The quantities of P and Q can be controlled according to the installation’s needs.

The values ​​of P and Q can be determined by a supervisory and control system external to the inverter. The amount of reactive power injected by the inverter must respect its capacity curve.